Week 6 : Off to Jalan Pasar

                                                   Assalamualaikum and hello guys.

                   Before we proceed to our project progress, I want to apologize to all of the readers especially to my supervisor for not updating my blog for a few weeks. because we just learned from our friends.But we try to meet supervisor for update the our project progress. As we mention before Our project will consist two circuit :

• ULTRA SONIC MOTION DETECTOR 

• IC TIMER 

       We would like to show you a part of component's that we bought at Jalan Pasar. I did not put all the component in today's entry due to the component that still not been purchased. 

         We search every single place at Jalan Pasar, but we are only get a few of components. It is because we  are arrived late from our estimation time.  InshaAllah, we will go back there to get all next weekend ..

   

         This is the one of our receipt, another receipt because of the several technical problems. InsyaAllah,we will upload it in next entry..

 

Week 5 : Our Components ..

                                    Assalamualaikum & Have a nice day, readers !

           Alhamdulillah, Now we discuss with supervisor and show our project progress to her. May Allah give   forgiveness and a lot of mercy for us, Insya-Allah..

           After doing some research and discussion about our project, we are able to list down our component that we need in our project. This is require us to go to Jalan Pasar, Kuala Lumpur to obtain the necessary item, I mean an electronics component, and all of the devices that we need for our project. 

For this project, we need to construct two circuits

 ULTRA SONIC MOTION DETECTOR:

1.Resistor (33ohm,1M,2.2M,1K,6.8K,470K,10K,100K)
2.Capacitors (330mF,1mF,4.7mF,10mF,0.001mF,0.01mF,0.1mF,30pF)
3.IC1 CMOS 4069
4.IC2 TL 084
5.Q1 Q2 IN 4001 until 4007                                                       
6.D1 D2 IN 4001 until 4007
7.D3,D4,D5 IN 4148
8.Zener Diode 400 mW
9.VR Trimmer Pot (preset) (10,15,20,22kohm)
10.K1 Relay DC12V
11.LED 5mm
12.XTAL tuning fork crysstal 40KHz
13.TD1 40KHz Ultrasonic transducer (Transmitter,40T)
14.TD2 40KHz Ultrasonic transducer (receiver,40R)               


IC TIMER:

1.Resistors (10K,5.6K,5.1K,100K,680 Ohm)               
2.8-pin IC Socket-1pc                                                   
3.D1 1N4148 or 1SS133
4.D2 Rectifier Diode 1N4001,1N40002
5.Electrolytic Capacitors (47mF,2.2mF,330mF)

6.Ceramic Capacitors (0.01mF,0.022mF)              

7.Q1 NPN Transistors (2SC1815,2SC945)                   

8.LED1 5mm
9.VR1 1M ohm                                         
10.S1 Range
11.S2 Start'
12.S3 Reset
13.RLY- Relay DC9V
14. IC1 8 Pin Integrate Circuit(Timer IC)

Week 4: Our Greatest Plan

                                    Assalamualaikum and hello to all reader...^_^..

On this week we are starting for doing the draft report. because our supervisor want to see  draft report early..but actually  we have to prepare plan to make sure our vision will accomplish on time.So  using Microsoft project software, we are creating a Gantt Chart in order to ensure that our project construction progress will be proceeded smoothly.


                                  Our Gantt Chart planner are shown as below. 

We will try to follow the procedure as best as we can. So that will help us to complete our project on time. But in the same time we also do it instruction by supervisor madam Naszariah Mohd Noor May ALLAH Bless our project progress..^_^..